Electrical Panel Upgrades · Belmont, California

Electrical Panel Upgrades in Belmont, CA

Upgrading an electrical panel — typically 100A to 200A — to add capacity for EV chargers, heat pumps, induction ranges, and modern loads, including Federal Pacific and Zinsco replacements.

Get a Free Estimate →

CSLB #1145945 PG&E Handled Upfront Pricing

15+

Years Experience

5.0★

Google Rating

2 hr

Quote Response

Electrical Panel Upgrades for Belmont Homes

Belmont sits in the hills between San Carlos and San Mateo, and most of the homes here went up in the 1950s and 60s as ranches and split-levels stepped into the slope. They were built with 100-amp service, and on a hillside in 1958 that was plenty. It is not plenty for a household that wants to charge an EV in the carport, run a heat pump, and cook on induction. What makes a Belmont panel upgrade its own animal is the terrain. In Belmont Hills, Carlmont, and Upper Belmont, the meter and main often sit at the bottom of a long run from the street, sometimes in underground conduit that climbs the lot, so sizing the new service is only half the job. The other half is the routing. The flatter Sterling Downs and Cipriani blocks are more straightforward, but even there the original split-level layouts hide the panel in a garage or a stair landing that takes some planning to feed cleanly. Fox Electric upgrades these Belmont services to a modern 200-amp panel, sized with a real load calculation so there is headroom for whatever you add next, and we plan the work around the hillside rather than fighting it. We are based next door in San Carlos, so we reach any Belmont neighborhood in a few minutes.

Permits & utility in Belmont

Electrical service for Belmont is provided by PG&E, and the electrical permit and inspection go through the local building department. We pull the permit and coordinate the PG&E service work as part of the job.

Belmont sits in PG&E territory, so the service disconnect and reconnect is coordinated with PG&E while the permit and inspection go through the City of Belmont building department. The hillside construction is the real variable here: long underground runs from the street in Belmont Hills and Upper Belmont add conduit and trenching considerations a flatland panel swap never sees, and weather exposure on west-facing lots argues for proper outdoor-rated equipment. We confirm the panel location and the run condition during the load walkthrough so there are no surprises on install day.

Pricing depends on your home and scope — we give a free on-site estimate with a written, fixed price before any work starts. For typical Bay Area ranges, see our guide on what a panel upgrade costs in the bay area.

What's Included

Electrical Panel Upgrades in Belmont

Load calculation to size the new service correctly

New 200A main panel (Eaton, Square D, or Siemens) and meter coordination

Federal Pacific / Zinsco fire-risk panel replacement

Sub-panel additions for garages, ADUs, and EV circuits

City permit pulled and electrical inspection closed out

Every circuit labeled and the panel directory typed

How We Handle Electrical Panel Upgrades in Belmont

Straightforward, permitted, and clean — from your first call to final sign-off in Belmont.

Load Assessment

A licensed Fox electrician runs a load calculation and gives you a written fixed-price quote — no surprises.

Permit & Utility Scheduling

We pull the city electrical permit and schedule the service disconnect/reconnect with your utility.

Install Day

Power off, old panel out, new 200A service in, every circuit relabeled — usually one working day.

Inspection & Reconnect

City inspection passed, utility reconnects, and you keep the permit closeout for resale.

Recent Project

200A Panel Upgrade — Belmont200A Upgrade

A Belmont homeowner needed more capacity for an EV charger and a future heat pump, but the home was still on its original 100A service. We ran a load calculation, pulled the city permit, coordinated the PG&E service window, and installed a 200A panel — every circuit relabeled and the directory typed, powered back up the same day.

Before: Original 100A service, no room to grow
After: 200A panel sized for EV + heat pump headroom
Coordination: PG&E disconnect/reconnect + city inspection handled
Outcome: Passed inspection, permit closed out for resale

The Fox Difference

Why Belmont Chooses Fox Electric

Local to Belmont

Based in San Carlos — 5 min away. We know Belmont homes, PG&E coordination, and the local permitting.

Licensed & Insured

CSLB #1145945 — fully licensed C-10 contractor and bonded. Every job permitted and inspected to current code.

Permits & Utility Handled

We pull the Belmont permit, coordinate PG&E service work, and close out the inspection — you schedule one day, we do the rest.

5.0★ on Google

We earn the rating on every visit, not just the first.

Upfront, Fixed Pricing

Free on-site estimate with a written fixed-price quote before any work starts. No obligation, no surprises.

Same-Day Availability

We hold same-day slots open for Belmont homeowners when something can't wait.

Questions

Electrical Panel Upgrades in Belmont — FAQ

Does a Belmont panel upgrade go through PG&E or the city?

Both, in their lanes. PG&E handles the actual service disconnect and reconnect at the meter, and the City of Belmont building department issues the electrical permit and sends an inspector. We coordinate the PG&E window and pull the city permit for you, so you are not chasing two agencies.

My Belmont home has a long run up the hill from the street. Does that change the upgrade?

It can. Many Belmont Hills, Carlmont, and Upper Belmont lots have the service climbing the slope in underground conduit, so we check the condition and capacity of that run before quoting. If the conduit and feed are sound we reuse them; if the upgrade calls for a heavier feed, we plan that into the scope up front rather than discovering it mid-job.

My 1950s Belmont ranch still has a 100-amp panel and we want an EV charger. Do we need 200 amps?

Often yes, but we confirm it with a load calculation before quoting an upgrade. Sometimes a load-management device lets the existing service carry the charger and saves you the panel work entirely. If you are also eyeing a heat pump or induction range, a 200-amp upgrade usually makes the next install plug-and-play.

Is the original wiring behind the panel ever a problem in Belmont homes?

Sometimes. Belmont's 1950s-60s housing stock often has exposed or original-era branch wiring behind that 100-amp panel, and we look at it during the walkthrough. We will tell you honestly whether the panel upgrade stands on its own or whether a section of wiring is worth addressing at the same time, without pushing a full rewire you do not need.

How long is my power off for a panel upgrade in Belmont?

Usually one working day. Power is off while we swap the panel and PG&E handles the disconnect and reconnect, then the City of Belmont inspects before final re-energization. We schedule the PG&E window in advance so you can plan around a single day without power.